Stone Rhino 43 Series Скачать руководство пользователя страница 61

Страница: 61 / 66

Maintenance

Rhino

43/54

TROUBlESHOOTING

Brakes don’t hold properly.

Brake valve faulty.

Check brake light operation.

Check for 12 volt A brake valve, see
wiring.

Loose wires.

Check wiring for loose or broken wiring.

Brake stays on.

No release pressure.

Check pump for proper charge pressure
220-260psi.

Faulty relay.

Check, replace if required.

Undercharged system.

Excessive electrical load from
added accessories.

Remove accessories.

Excessive engine idling.

Increase RPM when heavy electrical load
is used.

Poor electrical connections on
bettery, ground strap, starter or
alternator.

Inspect and clean as neccesary.

Defective battery.

Test battery.

Defective alternator.

Test charging system.

Battey used too much water.

Cracked battery case.

Check for moisture and replace as
neccesary.

Defective battery.

Test battery.

Battery charging rate too high.

Test charging system.

Battery will not charge.

Loose or corroded connections.

Clean and tighten connections.

Sulfated or worn out battery.

Replace battery.

Loose or defective alternator
belt.

Adjust belt tension or raplace belts.

Starter will not crank

Loose or corroded connections.

Clean and tighten loose connections.

Low battery output voltage.

See your authorized service dealer or
engine distributor.

Faulty start circuit relay.

See your authorized service dealer or
engine distributor.

Starter cranks slowly.

Low battery output.

See your authorized service dealer or
engine distributor.

Crankcase oil too heavy.

Use proper viscosity oil.

Loose or corroded connections.

Clean and tighten loose connections.

Entire electrical system does not function

Faulty battery connection.

Clean and tighten connections.

Sulfated or worn out battery.

Replace battery.

Blown fuse.

Replace fuse.

Содержание Rhino 43 Series



































































Результаты поиска

Содержание Rhino 43 Series

Отзывы:

Stone Rhino 43 Series, Руководство оператора, Страница: 61 / 66

Результаты поиска

Содержание Rhino 43 Series

Отзывы: