Stone Rhino 43 Series Скачать руководство пользователя страница 41

Страница: 41 / 66

Maintenance

Rhino

43/54

IMPORTANT MAINTENANCE INFORMATION

Remove the key and / or disconnect battery to avoid accidental ignition of en-

gine. Severe personal injury may occur. Roller must be parked on level ground

with parking brake applied, engine off, and drum blocked. Never work on the

roller with engine running. Severe personal injury may occur. Allow all compo-

nents in the engine compartment to cool before performing any service work.

IMPORTANT: Read Kubota Engine Manual before service or maintenance.

ADDITIONAl SERVICE INFORMATION

This is not a detailed service manual. If you want more detailed service information see
Kubota Manuals: 56956 Manual Workshop Kubota V3600

ENGINE OIl AND FIlTER

IMPORTANT

: Read Engine Manual and Engine Break-in covered in Operating section of

this manual.

Change oil and filter at 50 hours, then every 500 hours. Use SAE 15W-40 API CG-4 or API
CF-4.

1. Run engine approximately 5 minutes to warm up oil. Shut engine off.

2. Remove oil pan drain plug, drain into suitable container.

3. Drain crankcase oil from engine while warm.

4. Remove and discard oil filter using a filter wrench.

5. Clean filter mounting pad.

IMPORTANT

: Filtration of oils is critical to proper lubrication. Always change filter regu-

larly. Use filter meeting Kubota performance specifications.

6. Oil new filter seal and install new filter element, tighten approximately 3/4 – 1

- 1/4 turn after packing contacts filter housing. DO NOT overtighten filter ele-
ment.

7. Install oil pan drain plug.

8. Fill engine crankcase with correct engine oil.

IMPORTANT:

Immediately after completing any oil change, crank engine for 30 seconds

without permitting engine to start. This will help insure adequate lubrication to engine
components before engine starts.

9. Start engine and run to check for possible leaks.

10. Stop engine and check oil level after 10 minutes. Oil level reading should be

between arrows or within crosshatch of dipstick.

WARNING

Содержание Rhino 43 Series



































































Результаты поиска

Содержание Rhino 43 Series

Отзывы:

Stone Rhino 43 Series, Руководство оператора, Страница: 41 / 66

Результаты поиска

Содержание Rhino 43 Series

Отзывы: