Stone Rhino 43 Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 66

Stone Rhino 43 Series Скачать руководство пользователя страница 32

2

Operation

Rhino

TM

43/54

PARkING THE MACHINE

Always use care when parking the machine. Do not park on unstable ground or in an
unsafe position. Observe the following caution: Never park the roller on an incline. The
roller may creep forward or reverse even when engine is off. Tipping may occur resulting
in personal injury or engine damage.

• Return the control lever to the NEUTRAL position.

• Ensure machine is stationary on firm ground.

• Idle engine 2-3 minutes.

• Turn the key to the OFF position to stop the engine and set brakes. Remove

ignition key.

• Chock drum.

SAFETY FEATURES

To help prevent accidents, the machine is equipped with the following safety features.
Check safety features daily. It is the driver’s responsibility to operate the machine safely.

Neutral Interlock

The neutral interlock switch should not allow the engine to start unless the forward/re-
verse lever is in NEUTRAL and the operator is firmly seated. The forward/reverse lever
should be aligned with “NEUTRAL” on the console when the roller is moving neither
forward nor backward with the engine running.

Seat Interlock

Seat interlock is controlled by a switch operated by the weight of the operator on the
seat. The engine cannot be started unless operator is firmly seated facing forward. Seat
belts MUST ALWAYS be worn.

ROPS/FOPS

The roller is equipped with a roll-over protection structure - ROPS and a falling object
protection structure - FOPS.

DO NOT operate this machine if the roll-over protection structure (ROPS/FOPS) is missing
or structurally damaged, shows cracks, is not properly secured as originally installed or
has been rolled.

DO NOT repair, modify, or add attachments to the ROPS unless authorized in writing by
the manufacturer.

The seat belt must always be worn by the operator. In the event of a roll-over DO NOT
jump off the roller.

DO NOT add attachments to the machine that intrude into operator’s protective

area, reduce visibility, restrict emergency exits, or add weight exceeding certifi-
cation weight of ROPS. DO NOT operate machine unless seat belt conforming to

SAE and/or ASAE standards is fastened. See Operator’s Manual or contact your

dealer for complete inspection requirements and maintenance instructions.

WARNING

«
...
30
31
32
33
34
...
»

Содержание Rhino 43 Series



































































Отзывы:

Нет отзывов