Stone Rhino 43 Series Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 66

Stone Rhino 43 Series Скачать руководство пользователя страница 19

1

Health &

Safety

Rhino

TM

43/54

FOllOW SAFETY INSTRUCTIONS

• Carefully read all safety messages and decals in this manual and on your ma-

chine safety signs. Keep decals in good condition. Replace missing or damaged
decals. Be sure new equipment components and repair parts include the current
safety signs. Replacement safety signs and decals are available through your
dealer.

• Learn how to operate the machine and how to use controls properly. Do not let

anyone operate without instruction.

• Keep your machine in proper working condition. Unauthorized modifications to

the machine may impair the function and/or safety and affect machine life.

• If you do not understand any part of this manual and need assistance, contact

your dealer.

UNDERSTAND SIGNAl WORDS

• A signal word – DANGER, WARNING, or CAUTION – is used with the safety-alert

symbol. DANGER identifies the most serious hazards.

• DANGER or WARNING safety signs are located near specific hazards. General

precautions are listed on CAUTION safety signs. IMPORTANT also calls attention
to safety messages in this manual.

• This notation appears before warnings in the text. It means that the step that

follows must be carried out to avoid the possibility of personal injury or death.
These warnings are intended to help the technician avoid any potential hazards
encountered in the normal service procedures. We strongly recommend that the
reader takes advantage of the information provided to prevent personal injury or
injury to others.

PRACTICE SAFE OPERATION

• Users must be trained to operate this roller. Read the Operator’s Manual and

Engine Owner’s Manual. Learn to operate this roller safely.

• Only start engine from operator’s seat.

• Operator must always be seated when roller is running.

• Never allow more than one person on roller.

• Before starting machine, make sure that there are no persons or obstacles near

or under machine.

• Always turn engine off before dismounting from roller.

• Never park roller on a hill.

• Never operate roller on slope greater than 15 degrees.

• Do not operate across the sides of hills, roller may tip over.

• Do not articulate on grades larger than 15

o

, roller may tip over.

• Do not operate the roller in standing water.

• Do not operate at the edge of mats or roads, roller may tip over.

WARNING

«
...
17
18
19
20
21
...
»

Содержание Rhino 43 Series



































































Отзывы:

Нет отзывов