Stone Rhino 43 Series Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 66

Stone Rhino 43 Series Скачать руководство пользователя страница 37

Operation

Rhino

TM

43/54

TIE DOWNS

The roller is equipped with front and rear tie down points for shipping purposes. Use only
these points to secure unit. Tie downs may be used in emergency or breakdown.

• When loaded, the roller must be secured using chains, ropes, straps, etc. of suf-

ficient strength to hold the roller safely in all circumstances.

• The tie down points on each side, must be used in conjunction with those on the

trailer or lorry.

Ensure the following:

1. Control Lever is in the Neutral Position

2. Ignition Key has been Removed

3. Locking bar is in position to prevent the front and rear frames from articulating

randomly.

Suggested method for securing roller to trailer bed/truck

Tie downs are not intended for lifting purposes.

Equipment is equipped with front and rear tie down points for shipping purposes. Use
only these tie downs to secure unit.

Place chocks as shown and nail to Truck/Trailer bed.

Block frame on two sides to avoid overloading drum islolators.

Securing Roller for Transport

Tie Down Point

Tie Down Point

Lashing chain,

rope, strap,

etc.

Lashing chain,

rope, strap, etc.

WARNING

«
...
35
36
37
38
39
...
»

Содержание Rhino 43 Series



































































Отзывы:

Нет отзывов