Stone Rhino 43 Series Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 66

Stone Rhino 43 Series Скачать руководство пользователя страница 55

55

Maintenance

Rhino

TM

43/54

CHARGE SYSTEM

If gauge fails to function, check charge system. With the engine running at full speed,
voltage should be 13-14 volts across the battery (check volt meter). If unit is charging,
replace gauge. If not, see authorized engine dealer to check alternator.

PANEl FUSE 20 AMP

This fuse provides protection for the electrical system. If the engine fails to turnover
when starting, check the fuse.

Never use fuse with a different rating from that specified. Seri-

ous damage to the electrical system or a fire may result.

Turn the engine switch off and remove the key before checking or replacing fuses to
prevent accidental short-circuiting.

When frequent fuse failure occurs, it usually indicates a short circuit or an overload in
the electrical system. See your authorized engine dealer for repair.

ENGINE INSTAllATION GUIDElINES

When installing new or reworking used diesel engines, this list of guidelines should be
strictly adhered to. Following these guidelines should prevent damage to the electrical
system of diesel engines.

A. Always disconnect the negative cable from the battery before performing any

work on the machine that involves welding or working on the electrical system.

B. Avoid jump starting a diesel engine. Either change the battery or remove the

negative cable and charge the battery.

C. Do not alter or change the wiring harness.

D. Cold weather add-ons should not be needed.

When cleaning machine, caution should be used around alternator area. Direct spraying
of the alternator is not good. (Alternator should be covered or protected if direct spray-
ing will happen). Excessive water pressure may also loosen wire connections or cause
terminal corrosion. After cleaning, all terminals should be dried if wet and connections
checked for proper seating.

ENGINE MOUNTING

Check periodically, tighten all mounting hardware for proper torque. Refer to Torque
Charts in Exploded Views with Parts Section.

HARDWARE

Inspect all hardware for tightness. Refer to parts illustrations for proper torque and
Torque Charts in Exploded Views with Parts Section.

WARNING

«
...
53
54
55
56
57
...
»

Содержание Rhino 43 Series



































































Отзывы:

Нет отзывов