Stone Rhino 43 Series Скачать руководство пользователя страница 3

Страница: 3 / 66

Rhino

43/54

LIMITED WARRANTY ....................................................................................... 5
FOREWORD ................................................................................................... 6

INTRODUCTION .............................................................................................. 7 - 8

TECHNICAL DATA ........................................................................................... 9 - 16

Specifications .................................................................................... 10 - 11

Engine RPM ....................................................................................... 10 - 11

Machine Data .................................................................................... 12

Operator Controls ............................................................................... 13

Machine Sound Level Test ................................................................... 14

Locking Bar ....................................................................................... 14

Machine Dimensions ........................................................................... 15 - 16

HEALTH & SAFETY ......................................................................................... 17 - 24

OPERATION ................................................................................................... 25 - 38

Delivery Inspection ............................................................................ 26

Break-in Period.................................................................................. 26

Before Starting .................................................................................. 26

Warming Engine ................................................................................. 27

Fuel ................................................................................................. 27

Engine Oil Level ................................................................................. 28

Air Filter / Fuel Level ......................................................................... 28

Hydraulic Oil ..................................................................................... 28

Engine Coolant .................................................................................. 28

Tires/Lug Nuts .................................................................................. 29

Drum/Scrapers .................................................................................. 29

Cleaning ........................................................................................... 29

Eccentrics ......................................................................................... 29

Visual Inspection ............................................................................... 30

Mounting/Dismounting the Machine .................................................... 30

Starting the Machine .......................................................................... 30

Cold Weather Starting......................................................................... 30

To Operate ........................................................................................ 31

Operation on Slopes ........................................................................... 31

Forward/Reverse/Neutral .................................................................... 31

Shutting the Machine Off .................................................................... 31

Parking the Machine .......................................................................... 32

Safety Features .................................................................................. 32

Seat ................................................................................................. 33

Steering Controls ............................................................................... 33

Operator Controls ............................................................................... 34

Gauges ............................................................................................. 35

Lights ............................................................................................... 35

Air Cleaner ........................................................................................ 35

Compaction Tips ................................................................................ 36

Locking Bar ....................................................................................... 36

Transportation ................................................................................... 36

Tie Downs ......................................................................................... 37

Towing (Bypass) ................................................................................ 38

Storage ............................................................................................. 38

MAINTENANCE ............................................................................................... 39 - 64

Important ......................................................................................... 40

Maintenance Schedule ........................................................................ 40

Important Maintenance Information .................................................... 41

Additional Service Information ............................................................ 41

Hydraulic Oil/Filter ............................................................................ 42

Hydraulic Breather ............................................................................. 43

Table of

Contents

Содержание Rhino 43 Series



































































Результаты поиска

Содержание Rhino 43 Series

Отзывы:

Stone Rhino 43 Series, Руководство оператора, Страница: 3 / 66

Результаты поиска

Содержание Rhino 43 Series

Отзывы: