manualshive.com logo in svg

Stone Rhino 43 Series, Руководство оператора, Страница: 28 / 66

Поделиться
Скачать
Stone Rhino 43 Series Скачать руководство пользователя страница 28

2 

Operation

Rhino

TM

 43/54

Keep the vent hole in fuel tank cap open. If vent hole is plugged, pressure may 

build up in tank, causing dangerous spraying of fuel when cap is removed. A 

vacuum may also be created during operation, which could stop fuel flow.

ENGINE OIl lEVEl

Change oil at 50-hours, then every 500-hours. Check engine oil before starting when 
engine is cold, roller is parked on level ground and engine is off. See Machine Data for 
engine oil type. Do not overfill.

AIR FIlTER

Check air filter before starting, clean if dirty. See Maintenance for air filter cleaning.

FUEl lEVEl

Check the fuel level when the roller is parked on level ground and the engine is off. Use 
the sight tube on the fuel tank to check fuel level. 

HYDRAUlIC OIl

Pressurized release of fluids from hydraulic system can cause serious burns. 

Shut off engine. Only remove breather cap when cool enough to touch with bare 

hands. Slowly loosen cap to relieve pressure before removing completely.

Check the hydraulic oil level.  Use the sight gauge located on the hydraulic tank.  A 1/4 
– 1/2” air bubble will be seen at the top of the gauge showing the fluid level.

For satisfactory operation, the following oil conditions apply:

1.  Accurate level readings can be checked only when the fluid is cold.

2.  If the natural color of the fluid has become black or milky, it is possible that an 

overheating or water contaminant problem exists.

3.  Do not mix hydraulic fluids.  Mobilfluid 424 is recommended for the hydraulic 

system.

CAUTION:  After a new unit has run 50 hours, the oil filter should be changed.  This is 
to rid the system of any trapped contamination from the wear-in of the parts.  Refer to 
Maintenance for hydraulic filter change.

ENGINE COOlANT

Check cooling system carefully.  Explosive release of fluids from 

pressurized cooling system can cause serious burns.  

To check coolant level:

1.  Shut off engine, allow to cool.

WARNING

WARNING

WARNING

Содержание Rhino 43 Series



































































Отзывы:

Нет отзывов