manualshive.com logo in svg

Stone Rhino 43 Series, Руководство оператора, Страница: 26 / 66

Поделиться
Скачать
Stone Rhino 43 Series Скачать руководство пользователя страница 26

2 

Operation

Rhino

TM

 43/54

WARNING

DElIVERY INSPECTION

Upon receipt of your roller, CAREFULLY CHECK FOR ANY FREIGHT DAMAGE.  Any damage 
should be immediately reported to the carrier and a claim registered.

Rhino is manufactured to the strictest specifications and inspection procedures.  If any 
material or manufacturing defects are found, return the tag on the machine with the 
assembler’s signature and your findings to the manufacturer.  We want to know when a 
product is less than perfect.  We also welcome any and all input on how the product may 
serve you better.

The following instructions were compiled to provide you information on how to obtain 
long and trouble free use of the roller.  Periodic maintenance of the roller is essential.  
Read the manual in its entirety and follow the instructions carefully.   Refer to the Tech-
nical Data Section to familiarize yourself with machine controls and components. Failure 
to do so may injure yourself or a bystander.

BREAk-IN PERIOD

The Rhino roller is ready for normal operation.  However, extra care during the first 50 
hours of operation will result in more satisfactory, long-term machine performance and 
cost of ownership.  Do not exceed 50 hours of operation before conducting the break-in 
first service.  See First Service 50 Hours in the Maintenance Section.

•  Run engine at full throttle.

•  Run engine under load.  DO NOT overload the engine.

•  Idle engine 3 minutes before stopping.

•  DO NOT idle engine for long periods.

•  Check engine oil level daily.

BEFORE STARTING

Review the following information.  Specific information regarding these items can be 
found in the Technical Data Section or located by the Table of Contents.

Fuel is highly flammable, handle with care.  Do not refuel the engine 

while smoking or when near an open flame or sparks.  Always stop en-

gine before refueling.  Clean up spilled fuel before starting.  Avoid 

fires by keeping engine clean of accumulated grease and debris.

Diesel fuel stored in galvanized containers reacts chemically with the zinc coat-

ing on the container.  The chemical reaction creates powdery flakes of zinc 

sulfide.  If water is present in the fuel, a zinc hydroxide gel will form.

Do not run unit in an enclosed, unventilated area.  Avoid 

prolonged breathing of exhaust gases.

Содержание Rhino 43 Series



































































Отзывы:

Нет отзывов