Stone Rhino 43 Series Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 66

Stone Rhino 43 Series Скачать руководство пользователя страница 49

Maintenance

Rhino

TM

43/54

BlADE PINS

Grease the two fittings daily; one on each of the blade pivot pins.

BATTERY

Servicing Battery

Battery gas can explode. Keep sparks and flames away from batteries. Use a flashlight
to check battery electrolyte level.

Never check battery charge by placing a metal object across the posts. Use a voltmeter or
hydrometer.

Always remove grounded negative (-) battery clamp first and replace it last.

1. On regular batteries, check electrolyte level. Fill each cell to bottom of filler

neck with distilled water.

2. Keep batteries clean by wiping them with a damp cloth. Keep all connections

clean and tight. Remove any corrosion, and wash terminals with a solution of 1
part baking soda and 4 parts water. Tighten all connections securely.

NOTE: Coat battery terminals and connectors with a mixture of petroleum jelly and bak-
ing soda to retard corrosion.

3. Keep battery fully charged, especially during cold weather. If a battery charger

is used, turn charger off before connecting charger to battery(ies).
Attach POSITIVE (+) battery charger lead to POSITIVE (+) battery post. Then at-
tach NEGATIVE (-) battery charger lead to a good ground.

Once a month, check the battery for proper charge of 12.5 volts. Check for proper fluid
level. Use distilled water when adding and run 30 minutes to mix. Clean battery, posts,
and terminals. Disconnect battery cables before charging to avoid damage to the electri-
cal system.

Sulfuric acid in battery electrolyte is poisonous. It is strong enough to burn

skin, eat holes in clothing, and cause blindness if splashed into eyes.

If acid is spilled on skin or swallowed, seek medical attention immediately!

Avoid the hazard by:

1. Filling batteries in a well-ventilated area.

2. Wearing eye protection and rubber gloves.

3. Avoiding breathing fumes when electrolyte is added.

4. Avoiding spilling or dripping electrolyte.

5. Use proper jump start procedure.

If you spill acid on yourself:

1. Flush your skin with water.

2. Apply baking soda or lime to help neutralize the acid.

3. Flush your eyes with water for 10 – 15 minutes. Get medical attention immedi-

ately.

WARNING

«
...
47
48
49
50
51
...
»

Содержание Rhino 43 Series



































































Отзывы:

Нет отзывов