Stone Rhino 43 Series Скачать руководство пользователя страница 59

Страница: 59 / 66

Maintenance

Rhino

43/54

TROUBlESHOOTING

High fuel consumption.

Improper type of fuel.

Use proper type of fuel.

Clogged or dirty air cleaner.

Service air cleaner.

Engine overloaded.

Excessive mud/debris build-up, clean/
pressure wash.

Improper valve clearance

See your authorized service dealer or
engine distributor.

Injection nozzles dirty.

See your authorized service dealer or
engine distributor.

Engine out of time.

See your authorized service dealer or
engine distributor.

Low engine temperature.

Check thermostat.

High oil consumption.

Crankcase oil too light.

Use proper viscosity oil.

Oil leaks.

Check for leaks in lines, gaskets and drain
plug.

Restricted crankcase vent tube.

Clean vent tube.

Defective turbocharger.

See your authorized service dealer or
engine distributor.

Too much oil in crankcase.

Drain, fill to proper level.

Loose oil filter or sending unit.

Tighten.

Loose bolts.

Tighten.

Engine in break-in period.

See Engine Owner’s Manual.

Low oil pressure.

Low oil level.

Add oil.

Improper type of oil.

Drain, fill crankcase with oil of proper
viscosity and quality.

Engine emits smoke.

Too much oil in crankcase.

Drain, fill to proper level.

Engine in break-in period.

See Engine Owner’s Manual.

Engine emits white smoke.

Improper type of fuel.

Use proper fuel.

Low engine temperature.

Warm up engine to normal operating
temperature.

Defective thermostat.

Remove and check thermostat.

Defective injection nozzles.

See your authorized service dealer or
engine distributor.

Engine out of time.

See your authorized service dealer or
engine distributor.

Engine emits black or gray exhaust smoke

Improper type of fuel.

Use proper fuel.

Clogged or dirty air cleaner.

Service air cleaner.

Injection nozzles dirty.

See your authorized service dealer or
engine distributor.

Engine out of time.

See your authorized service dealer or
engine distributor.

Содержание Rhino 43 Series



































































Результаты поиска

Содержание Rhino 43 Series

Отзывы:

Stone Rhino 43 Series, Руководство оператора, Страница: 59 / 66

Результаты поиска

Содержание Rhino 43 Series

Отзывы: