Stone Rhino 43 Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 66

Stone Rhino 43 Series Скачать руководство пользователя страница 33

Operation

Rhino

TM

43/54

During a roll-over:

• Grip the steering wheel tightly with both hands and wait until the roller comes

to rest.

• Press the Emergency Stop Button.

• Dismount the roller immediately if it is safe to do so.

Horn

The horn should be used as a warning to others. The horn is operated by pressing the
button in the center of the steering wheel.

Back-Up Alarm

The Back-Up Alarm is located at the rear of machine. Alarm must activate whenever the
machine is moving in reverse.

SEAT

Adjustable suspension seat with seat belts.

Angle Adjustment

The seat backrest is adjustable for angle, sitting in the seat, turn the backrest adjustment
knob clockwise to recline or counter-clockwise to straighten backrest angle.

Seat Movement

The operator is able to adjust the seat in the fore-aft direction by actuating lever and
sliding seat to desired position, then releaseing lever to lock the seat into position.

Seat Belt

The seat is fitted with a seat belt for operator protection. Check operation daily and
always fasten seat belt before starting the machine. DO NOT modify or remove.

STEERING CONTROlS

This machine has center-point articulation power steering and always has priority flow
to the steering control valve. Turning the steering wheel will provide smooth steering in
both directions.

«
...
31
32
33
34
35
...
»

Содержание Rhino 43 Series



































































Отзывы:

Нет отзывов