Stone Rhino 43 Series Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 66

Stone Rhino 43 Series Скачать руководство пользователя страница 54

5

Maintenance

Rhino

TM

43/54

3. Adjustments must be made at transmission.

4. Disconnect ohmmeter and reconnect interlock wires and battery cables.

CONTROl CABlES: FORWARD/REVERSE, THROTTlE, BlADE

Lubricate all cable ends with penetrating oil every 200 hours.

D

o not adjust the control cable with the power on or the en-

gine running. Serious injury or death could result.

A gradual or sudden increase in the no-load friction (cable disconnect at both ends)

of a control cable is an indication of a pending or present performance problem.

The control cable should be replaced, otherwise serious injury or death could result.

A gradual or sudden decrease in the usable stroke is an indication of

a pending or present performance problem. The control cable should

be replaced, otherwise serious injury or death could result. Control ca-

bles which have moisture inside of them and/or have frozen should

be replaced. Do not apply heat to thaw or dry control cables.

ECCENTRICS

Test vibration with front drum on soft ground. Run engine at full rpm to obtain vibe
spec check per below. See Technical Data section for vibe speed.

To check vibration with a vibrotach, place the vibrotach on the vibrating member surface,
record reading when the wire reaches maximum movement. (Vibrotach P/N 37891).

When checking vibration with strobe light, place horizontal line on vibrating member
surface. Check with strobe light and record reading when the line reaches minimum
movement.

ECCENTRIC HOUSING OIl

Roller must be parked on level ground with parking brake applied and engine off.

Remove the key and / or disconnect battery to avoid acciden-

tal ignition of engine. Severe personal injury may occur.

Never work on the roller with engine running. Severe personal injury may occur.

Eccentric housing oil should be checked monthly and changed every 800 hours or yearly.
Refer to Maintenance Chart.

To check, locate oil plug inside the right hand drum end and position drum so that oil
plug is visible at 7:00. Loosen oil plug slowly until oil starts to drip out past the oil
plug. Oil must be present at the 7:00 position. Add oil if required and reinstall oil plug,
use thread sealant.

Eccentric housing oil:

SAE 20W/50 API SJ or API SH

SD/PD 43 1 qt. (.95 L.)

SP/PD 54 1.5 qt. (1.4 L.)

WARNING

WARNING

«
...
52
53
54
55
56
...
»

Содержание Rhino 43 Series



































































Отзывы:

Нет отзывов