Stone Rhino 43 Series Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 66

Stone Rhino 43 Series Скачать руководство пользователя страница 48

Maintenance

Rhino

TM

43/54

NOTE:

The proper installation is indicated when a “click” is heard and a release of the

retaining ring is felt. A plug is provided with the new element for plugging the used
element.

9. Bleed the fuel system. See Bleeding Fuel System in Maintenance section of this

manual.

FAN/AlTERNATOR BElT

Low belt tension causes slippage resulting in excessive cover wear, burn spots, overheat-
ing, or “slip and grab” causing belt breakage.

High belt tension causes belt heating and excessive stretch, as well as damage to drive
components such as pulleys and shafts. V-belts should ride on the sides of standard pul-
leys not on the bottom of the groove.

Standard V-belt tension can be checked with a tension gauge.

1. Inspect belts for cracks, fraying, or stretched out areas. Replace if necessary.

2. Using tension gauge and straightedge, check tension of warm belts.

– For standard V-belt, an 89 N (20 lb. force) applied halfway between pulleys
should deflect belt by 19 mm (3/4 in.).

3. If adjustment is necessary, loosen alternator bracket cap screw and nut on

mounting bolt. Pull alternator frame outward until belts are correctly

tensioned.

IMPORTANT:

Do not pry against the alternator rear frame. Do not tighten or loosen

belts while they are hot.

4. Tighten alternator bracket cap screw and nut firmly.

5. After a new or used belt has run for 10 minutes recheck belt tension.

Standard V-Belts

Tension New Belt

Tension Used* Belt

Single Belt

578-623 N

378-423 N

(130-140 lb. force)

(85-95 lb. force)

GREASE FITTINGS

Use a grease gun to grease the fittings. Remove the blue protection cap off fitting before
greasing.

FRAME HINGE

Grease daily six fittings with lithium base grease using a grease gun. There is one fitting
on each of the top and bottom bearings for the vertical pin. There are two fittings on
the horizontal pin.

«
...
46
47
48
49
50
...
»

Содержание Rhino 43 Series



































































Отзывы:

Нет отзывов