manualshive.com logo in svg

Stone Rhino 43 Series, Руководство оператора, Страница: 44 / 66

Поделиться
Скачать
Stone Rhino 43 Series Скачать руководство пользователя страница 44

 

Maintenance

Rhino

TM

 43/54

ADDING COOlANT

CAUTION:

  Explosive release of fluids from pressurized cooling system can cause serious 

burns.  Shut off engine.  Only remove filler cap when cool enough to touch with bare 
hands.  Slowly loosen cap to first stop to relieve pressure before removing completely.

IMPORTANT

:  Never pour cold liquid into a hot engine, as it may crack cylinder 

head or block.  DO NOT operate engine without coolant for even a few minutes.

Air must be expelled from cooling system when coolant is added.

1.  Loosen temperature sending unit fitting at rear of cylinder head to allow air to 

escape when  filling system.

IMPORTANT:  When adding coolant to the system, use the appropriate cool-

ant solution.  Coolant 50/50 mixture of antifreeze/distilled water meeting 

ASTM 4985, ASTM D5345 (pre-diluted coolant).  50/50 mixture provides pro-

tection to -34° F (-37° C).  Do not overfill cooling system.  A pressurized sys-

tem needs space for heat expansion without overflowing at top of radiato

r.

2.  Fill until coolant level touches bottom of radiator filler neck.

3.  Tighten fitting when air has been expelled from system.

DISPOSING  OF COOlANT

Improperly disposing of engine coolant can threaten the 
environment and ecology.

Use leakproof containers when draining fluids.  Do not 
use food or beverage containers that may mislead some-
one into drinking from them.

Do not pour waste onto the ground, down a drain, or into 
any water source.

Inquire on the proper way to recycle or dispose of waste 
from your local environmental or recycling center or from 
your dealer.

AIR ClEANER 

IMPORTANT:  Do not operate engine without the dust unloader valve.

For daily inspection refer to the Operating section of this manual.

Clean the primary (outer) filter element every 250 hours.
IMPORTANT:  Always replace secondary safety (inner) filter elements.  DO NOT attempt to 
clean them.  Do not blow air from outside portion of filter with air nozzle.  Wear safety 
glasses and remove bystanders.

1.  Remove air cleaner cover.

2.  Remove primary (outer) element only.

3.  Thoroughly clean all dirt from inside filter housing.

4.  Air cleaner has rubber dust unloader valve on the air cleaner.  Squeeze valve tip 

to release any trapped dirt particles.

Содержание Rhino 43 Series



































































Отзывы:

Нет отзывов