Spraying Systems Co 1550+ AutoJet, Руководство пользователя

Страница: 19 / 86

19
o
Connect suitable 1/2” O.D. tubing from the Liquid Inlet fitting to the liquid tote/tank.

Metric systems use 12 mm O.D. tubing
o
Customer to supply tubing
o
NOTE: For pump version systems the liquid source should not be pressurized
o
Connect suitable 1/2” O.D. tubing from the Liquid Out fitting to the corresponding fitting on the spray nozzle(s).
o
Tubing may be supplied with optional spray nozzle hook up kit
o
Note metric nozzle hook up kits are not available

Metric systems use 12 mm O.D. tubing
o Optional - Connect suitable 3/8” O.D. tubing from the Liquid In Return fitting to the liquid return line.
o
Tubing may be supplied with optional spray nozzle hook up kit only if it is a recirculating style hook up kit
o
Note metric nozzle hook up kits are not available
 Metric systems use 10 mm O.D. tubing
o Optional - Connect suitable 3/8” O.D. tubing from the Recirculation Liquid Out fitting to the return inlet of the liquid
source.
o
Customer to supply tubing
o
Metric systems use 10 mm O.D. tubing
Liquid Connections - Pump Less version
The 1550+ Pump Less Version is designed to control the pressure down from a pressurized source. If the system is supplied
with a pressure pot, the customer must supply air to the pressure pot. The liquid out line of the pressure pot must then be
connected to the Liquid In fitting on the 1550.
NOTE: Pump less version systems require the liquid source to be pressurized to a minimum of 10 psi above the maximum
application pressure. The maximum required application or discharge pressure must not exceed 100 psi.
NOTE: The Pump Less version is not designed to pressurize a vessel or pressure pot. Only to control the liquid pressure
from a pressurized source to the spray nozzles.
o
Connect suitable 1/2” O.D. tubing from the Liquid Inlet fitting to the liquid source.

Metric systems use 12 mm O.D. tubing
o
Tubing to be supplied by the customer.
o Connect suitable 1/2” O.D. tubing from the Liquid Out fitting to the corresponding fitting on the spray nozzle(s).
o
Metric systems use 12 mm O.D. tubing
o
Tubing may be supplied with optional spray nozzle hook up kit

Note metric nozzle hook up kits are not available
o Optional - Connect suitable 3/8” O.D. tubing from the Liquid In Return fitting to the liquid return line.
o
Metric systems use 10 mm O.D. tubing
o
Tubing may be supplied with optional spray nozzle hook up kit only if it is a recirculating style hook up kit

Note metric nozzle hook up kits are not available
o Optional - Connect suitable 3/8” O.D. tubing from the Recirculation Liquid Out fitting to the return inlet of the liquid
source.
o
Metric systems use 10 mm O.D. tubing
o
Tubing may be supplied with optional spray nozzle hook up kit only if it is a recirculating style hook up kit
o
Note metric nozzle hook up kits are not available
Liquid Connections – Pressure Pot version
The 1550+ Pressure Pot Version is designed to pressurize a vessel. It is not designed to receive pressurized fluid. It is not
designed to supply liquid directly to the spray nozzles. It only controls the air pressure going to the pressure pot. The
Pressure Pot system controls the flow of liquid using an internal manual liquid pressure regulator. This sets the air pressure
going to the pressure pot. For most materials the reading on the gauge should be close to the pressure at the liquid exit.
Note for high viscous and high-density materials this will deviate.
o Connect suitable 3/8” O.D. tubing from the Tank Air outlet fitting to the pressure pot air inlet.
o
Tubing supplied if system is purchased with standard pressure pot.

Metric systems use 10 mm O.D. tubing