manualshive.com logo in svg

SMC Networks JXCM1, Руководство по эксплуатации, Страница: 89 / 120

Поделиться
Скачать
SMC Networks JXCM1 Скачать руководство пользователя страница 89

- 88 - 

 

No.JXC#-OMX0009-A 

Controller 
supply 
voltage is 
outside set 
range. 
(01-147)

 

Over 
CrtlVol

 

D

 

RESET 

SVON

 

<Contents>   

The control power supply voltage within the controller is outside the set 
range.

 

<Countermeasure>   

Make sure that the voltage supplied to the control power (C24V) of the 
controller is appropriate. 

Caution

 

If a single power supply is used for both the control power and the 
motor power, or the power supply is "inrush-current control type", a 
power voltage drop may be caused due to a voltage drop during 
acceleration/deceleration. 

 

Current limit 
is exceeded 
(01-148)

 

Over load

 

D

 

RESET 

SVON

 

<Contents>

 

The output current accumulated value exceeds the specified value.

 

<Countermeasure>   

Make  sure  there  are  no  obstructions  that  interfere  with  the  electric 
actuator movement. Also, make sure that the load, speed, acceleration 
and deceleration are within the range of the electric actuator.

 

The target 
position was 
not reached 
within the set 
time limit 
(01-149)

 

Posn 
failed 
ALM

 

D

 

RESET 
SVON

 

<Content>

   

Failed to reach the set position within the set time limit.

 

<Content>

   

Make sure there are no obstructions that interfere with the 
electric actuator movement. Also, make sure that the load, 
speed, acceleration and deceleration are within the range of the 
electric actuator.

 

 

 

 

Содержание JXCM1

























































































































Отзывы:

Нет отзывов