manualshive.com logo in svg

SMC Networks JXCM1, Руководство по эксплуатации, Страница: 56 / 120

Поделиться
Скачать
SMC Networks JXCM1 Скачать руководство пользователя страница 56

- 55 - 

 

No.JXC#-OMX0009-A 

(4) Data editing function 

●

Controller 

→

  Higher level device [IN] (Remote to Master) 

PLC memory 

address

 

RWr data name

 

Contents

 

Half numerical 

data instructions

 

Full 

numerical 

data 

instructions

 

RWr 

bit 

0 

0 

C

ont
ro

ller 
inf

orm

at

ion 
flag

 

Return of Occupied 

number of stations (L)

 

Current occupied number of stations is shown. 

H 

L 

Occupied number of stations 

0 

0 

1 Stations occupied 

0 

1 

2 Stations occupied 

1 

0 

－

 

1 

1 

4 Stations occupied 

 

1 

Return of Occupied 

number of stations (H)

 

2 

Sending

 

After turning Start flag on at Step data editing function, 
this terminal will be ON during sending. And this 
terminal is OFF when the sending is completed or 
waiting for the sending instruction.

 

3 

Sending completed

 

When the data sending is completed at 

Step data 

editing function, Sending flag will be OFF and this 
terminal will be ON. Then Start flag turns OFF and this 
terminal will be OFF.

 

4 

READY

 

It is always ON if the controller has been started 
normally.

 

5 

ALARM flag

 

An alarm is generated when problems occur with the 
LECPMJ’s internal process or communication with the 
PLC. 
OFF during normal condition. ON when an alarm is 
generated.

 

6 

Initial

 

It is OFF during initial processing. It stays ON once 
the initial processing is completed.

 

7 

Numerical data reading 

enable/disable flag

 

It is ON when reading numerical data. Otherwise it is 
OFF.

 

8 

Parameter rewriting 

enable / disable flag

 

It is ON when the parameter rewrite flag is enabled. 
When it is disabled, it is OFF.

 

9 to C 

(No used)

 

－

 

D 

Data editing error 

receiving

 

When the error occurs in the data editing function

, this 

terminal will be ON with RWr0, bit5: ALARM flag. 
When RWw0, bit2: Reset is turned on, it is cleared.

 

E 

Parameter anomaly 

detection

 

When a parameter is invalid, this and the RWr0, bit5: 
ALARM flag are turned ON. It is turned OFF when the 
RWw0,bit2: Reset flag is turned ON. 
Please refer to 

"17. Alarm Detection for CC-Link 

Communication"

 for details.

 

F 

The abnormal station 

detection

 

When  an  abnormal  station  is  detected,  this  and  the 
RWr0, bit5: ALARM flag are turned ON. It is turned OFF 
when the RWw0,bit2: Reset flag is ON. 
Please refer to 

"17. Alarm Detection for CC-Link 

Communication"

 for details.

 

 

 

Содержание JXCM1

























































































































Отзывы:

Нет отзывов