Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 96

Страница: 96 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

9115

Float / 4

Fail-safe value

Output value in case of

a fault and when Fail-

safe behavior (9114) is

configured to 4.

0.0

[mA]

0.0 - 25.0

Read /

write

7153

Float / 4

Forced value

Forced value when

forcing is active.

4.0

[mA]

3.5 - 25.0

Read /

write

9186

Float / 4

Offset adjust‐

ment

Command to trim the

lower range value of

the loop current.
Simulate a loop current

of 4.0 mA, measure the

current with an ampere

meter and write the

measured value to this

0 - 25

Write on‐

9188

Float / 4

Gain adjustment Command to trim the

upper range value of

the loop current.
Simulate a loop current

of 20.0 mA, measure

the current with an am‐

pere meter and write

the measured value to

this register.

0 - 25

Write on‐

Channel 3 frequency output settings

Table 4-37

Channel 3 frequency output settings

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

9299

Unsigned / 2

Redundancy

mode

Redundancy mode.

● 0: Off. Channel 3 runs

independently.

● 1: 90°. Channel 3

follows frequency on
channel 2 with a 90°
shift.

● 2: 180°. Channel 3

follows frequency on
channel 2 with a 180°
shift.

Read /

write

9204

Unsigned / 2

Process value

Select process value

for the current output.

● 0: Mass flow
● 1: Volume flow
● 2: Density
● 3: Medium

temperature

Read /

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

Содержание SITRANS F Coriolis FCT030







































































































































































































Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы:

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 96 / 198

Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы: