Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 100

Страница: 100 / 198

Channel 3 pulse output settings

Table 4-38

Channel 3 pulse output settings

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

9280

Unsigned / 2

Redundancy

mode

Redundancy mode.

● 0: Off. Channel 3 runs

independently.

● 1: 90°. Channel 3

follows pulses on
channel 2 with a 90°
shift.

● 2: 180°. Channel 3

follows pulses on
channel 2 with a 180°
shift.

Read /

write

9260

Unsigned / 2

Process value

Select process value

for the pulse output.

● 0: Mass flow
● 1: Volume flow
● 27: Standard volume

flow rate (only
hydrocarbon and gas
applications)

Read /

write

9262

Unsigned / 2

Flow direction

Flow direction filter.

● 0: Positive direction
● 1: Negative direction
● 2: Positive and

negative directions

Read /

write

9265

Float / 4

Amount of vol‐

ume

Amount value to gener‐

ate an output pulse. Ap‐

plicable if process val‐

ue (9260) is set to 1.

0.001

]

(8993)

Read /

write

9263

Float / 4

Amount of mass Amount value to gener‐

ate an output pulse. Ap‐

plicable if process val‐

ue (9260) is set to 0.

1.0

[kg]

(8992)

Read /

write

9267

Float / 4

Amount of

standard vol‐

ume

Amount value to gener‐

ate an output pulse. Ap‐

plicable if process val‐

ue (9260) is set to 27.

1.0

[Sl]

(8994)

Read /

write

10155

Unsigned / 2

Pulses per

amount

Number of pulses

which will be output

when configured

amount is reached.

Read /

write

9274

Float / 4

Pulse width

Pulse duration.

0.1

[s]

0.00004 - 4.0

Read /

write

9277

Unsigned / 2

Polarity

Logical polarity of pulse

output.

● 0: Active high level
● 1: Active low level

Read /

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

100

Function Manual, 06/2018, A5E39931813-AB

Содержание SITRANS F Coriolis FCT030







































































































































































































Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы:

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 100 / 198

Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы: