manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 18 / 198

Поделиться
Скачать
Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 18

1. Deactivating buffers 
2. Updating the Electronic Device Description (EDD) 

Deactivating buffers for RS 485 COM port
This deactivation is required to align SIMATIC PDM for Windows® operating systems.

Note
Support for Windows operating systems can be found here: support.automation.siemens.com 

(

http://support.automation.siemens.com

)

1. Click Start → Control Panel to begin configuration.
2. Click on Hardware and Sound and then on Device Manager.
3. Open Ports folder and double-click the COM Port used by the system to open the 

Communications Port Properties window.
4. Select the Port Settings tab and click the Advanced button.
5. If the Use FIFO buffers check box is deselected, click to select.
6. Set Receiver Buffer and Transmitter Buffer to Low (1).

Figure 3-1

COM Port Setting

For serial adapters it can be required to change the Latency Timer (msec) to 1.

Commissioning
3.5 Initial Setup

FCT030 Modbus (From firmware 4.0)

18

Function Manual, 06/2018, A5E39931813-AB

Содержание SITRANS F Coriolis FCT030







































































































































































































Отзывы:

Нет отзывов