Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 162

Страница: 162 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[unit]

(unit register)

Value range /

Setting options

Access

level

7593

Unsigned / 2

Recipe 4 Dec.

point volume

flow

Specify the selected

number of decimals for

volume flow

Read /

write

7594

Unsigned / 2

Recipe 4 Dec.

point corrected

volume flow

Specify the selected

number of decimals for

corrected volume flow

Read /

write

9715

Float / 4

Recipe 4 fixed

compensation
Mass flow

Fixed compensation

mass flow value that is

used to close the

valve(s) before the

measured amount val‐

ue has reached the tar‐

get amount

Read /

write

9717

Float / 4

Recipe 4 fixed

compensation
Volume flow

Fixed compensation

volume flow value that

is used to close the

valve(s) before the

measured amount val‐

ue has reached the tar‐

get amount

Read /

write

9719

Float / 4

Recipe 4 fixed

compensation
Corrected vol‐

ume flow

Fixed compensation

corrected volume flow

value that is used to

close the valve(s) be‐

fore the measured

amount value has

reached the target

amount

Read /

write

9791

Unsigned / 2

Recipe 4 com‐

pensation mode

Compensation algo‐

rithm, fixed or adaptive

compensation

0: fixed compensation

value is taken
1: On Target
2: Target plus
3: Target minus

Read /

write

9725

Float / 4

Recipe 4 over‐

run mass flow

value

When the amount

mass flow has reached

this value a dosing

overrun fault is raised.

Read /

write

9727

Float / 4

Recipe 4 over‐

run volume flow

value

When the amount vol‐

ume flow has reached

this value a dosing

overrun fault is raised.

Read /

write

9729

Float / 4

Recipe 4 over‐

run corrected

volume flow val‐

When the amount cor‐

rected volume flow has

reached this value a

dosing overrun fault is

raised.

Read /

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

162

Function Manual, 06/2018, A5E39931813-AB

Содержание SITRANS F Coriolis FCT030







































































































































































































Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы:

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 162 / 198

Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы: