Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 40

Страница: 40 / 198

Function code 8 (Diagnostics)
The diagnostics function provides means for checking the communication between MODBUS

master and slave. The function uses a sub-function code to select the functionality.
The following sub-function codes are supported:

Sub-function code

Name

Description

Return query data

The data passed in the request data field will be returned (loo‐

ped back) in the response. The entire response message should

be identical to the request.

Restart communications option

After having restarted the communication, select the baudrate,

framing or Modbus address to get access to the device again.

Function code 17 (Report Slave ID)
The transmitter will respond to a Report Slave ID request from the master by giving information

about device type, vendor, and firmware version in a format as shown:
Response

Slave address

1 byte

Function code

1 byte

Byte count

1 byte

Slave ID

1 byte

Sensor device type

0: SITRANS FC

Run indicator

1 byte

255: Running

Manufacturer name 12 bytes

SIEMENS

Product name

32 bytes

SITRANS F

Product firmware

version

16 bytes

CRC

2 bytes

4.9

Access control

Access control manages whether the Modbus master is allowed to modify device parameters.

Reading of parameters is always possible. The general access control rules are:
● The Modbus interface has an access level that can be changed by providing PIN information

via the Modbus register 8292 (User PIN) or 8293 (Expert PIN).

● Each parameter has a protection level assigned that specifies the required access level to

modify the parameter via the Modbus interface.

● If the access level of the Modbus interface is lower than the protection level of the parameter

that is desired to be modified, then the attempt to modify the parameter is rejected by the

device.

MODBUS commands
4.9 Access control

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

Содержание SITRANS F Coriolis FCT030







































































































































































































Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы:

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 40 / 198

Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы: