Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 45

Страница: 45 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

8416

Float / 4

Totalizer 2 pre‐

set value

Preset value which will

be used when Totalizer

2 set is set to 2

-
(8321 / 8320 /

8322)

Read /

write

8419

Unsigned / 2

Totalizer 2 tar‐

get mode

Sets the desired mode

for the totalizer.

● 8. Auto, the totalizer

algorithm running

● 16: Man, the totalizer

algorithm is stopped.
The totalizer value
can be written

Read /

write

8500

Float / 4

Totalizer 3 value Totalized value of total‐

izer 3. Units depends

on the selected proc‐

ess value the totalizer

is configured to.

Write access if Totaliz‐

er 3 target mode is set

to 16: Manual

(8321 / 8320 /

8322)

Read /

write

8503

Unsigned / 2

Totalizer 3 set

Run, reset, or preset to‐

talizer 3.

● 0: Totalize
● 1: Reset
● 2: Preset to Totalizer

1 preset value

Read /

write

8504

Unsigned / 2

Totalizer 3 di‐

rection

Totalizer 3 direction.

● 0: Balanced
● 1: Positive
● 2: Negative
● 3: Hold

Read /

write

8516

Float / 4

Totalizer 3 pre‐

set value

Preset value which will

be used when Totalizer

3 set is set to 2

-
(8321 / 8320 /

8322)

Read /

write

8519

Unsigned / 2

Totalizer 3 tar‐

get mode

Sets the desired mode

for the totalizer

● 8. Auto, the totalizer

algorithm running

● 16: Man, the totalizer

algorithm is stopped.
The totalizer value
can be written

Read /

write

8549

Unsigned / 2

Reset all totaliz‐

ers

Reset command for to‐

talizers 1 to 3.

● 0: Run
● 1: Reset all totalizers
● 11: Reset totalizer 1
● 12: Reset totalizer 2
● 13: Reset totalizer 3

Write on‐

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

Содержание SITRANS F Coriolis FCT030







































































































































































































Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы:

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 45 / 198

Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы: