Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 108

Страница: 108 / 198

General channel 4 settings

Table 4-42

General channel 4 settings

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

9301

Unsigned / 2

Operation mode Operation mode.

● 0: Off
● 1: Current output
● 2: Frequency output
● 3: Pulse output
● 4: Signal output
● 5: Discrete input
● 6: Analog input

Read /

write

7440

Unsigned / 2

Active/passive

operation

Shows application

possibilities.

● 0: Active operation not

possible, use passive
wiring!

● 1: Active operation

possible, hardware is able
to drive the current loop.

Read

only

Channel 4 current output settings

Table 4-43

Channel 4 current output settings

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

9302

Unsigned / 2

Process value

Select process value

for the current output.

● 0: Mass flow
● 1: Volume flow
● 2: Density
● 3: Medium

temperature

Read /

write

9309

Unsigned / 2

Flow direction

Flow direction filter ap‐

plicable for Process val‐

ues (9302) = 0, 1, 19

and 27.

● 0: Positive direction
● 1: Negative direction
● 2: Positive and

negative directions

● 3: Positive and

negative directions
(symmetric mode)

Read /

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

108

Function Manual, 06/2018, A5E39931813-AB

Содержание SITRANS F Coriolis FCT030







































































































































































































Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы:

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 108 / 198

Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы: