manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 159 / 198

Поделиться
Скачать
Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 159

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[unit]

(unit register)

Value range / 

Setting options

Access 

level

9679

Unsigned / 2

Recipe 3 unit 

volume flow

Volume flow unit for 

dosing parameters 
 

41

40: US gallons
41: liters
42: imperial gallons
43: cubic meters
46: oil barrels
110: bushels
111: cubic yards
112: cubic feet
113: cubic inches
124: liquid barrels
170: beer barrels
236: hectoliters

Read / 

write

9680

Unsigned / 2

Recipe 3 unit 

corrected vol‐

ume flow

Corrected volume flow 

unit for dosing parame‐

ters 
 

166

166: normal cubic meters
167: normal liters
168: standard cubic feet
171: standard liters
172: standard cubic me‐

ters

Read / 

write

9608

Float / 4

Recipe 3 

amount mass 

flow

Target amount for dos‐

ing mass flow

-

-

Read / 

write

9610

Float / 4

Recipe 3 

amount volume 

flow

Target amount for dos‐

ing volume flow

-

-

Read / 

write

9612

Float / 4

Recipe 3 

amount correc‐

ted volume flow

Target amount for dos‐

ing corrected volume 

flow

-

-

Read / 

write

7589

Unsigned / 2

Recipe 3 Dec. 

point mass flow

Specify the selected 

number of decimals for 

mass flow

-

-

Read / 

write

7590

Unsigned / 2

Recipe 3 Dec. 

point volume 

flow

Specify the selected 

number of decimals for 

volume flow

-

-

Read / 

write

7591

Unsigned / 2

Recipe 3 Dec. 

point corrected 

volume flow

Specify the selected 

number of decimals for 

corrected volume flow

-

-

Read / 

write

9615

Float / 4

Recipe 3 fixed 

compensation
Mass flow

Fixed compensation 

mass flow value that is 

used to close the 

valve(s) before the 

measured amount val‐

ue has reached the tar‐

get amount

-

-

Read / 

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

159

Содержание SITRANS F Coriolis FCT030







































































































































































































Отзывы:

Нет отзывов