Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 112

Страница: 112 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

9386

Float / 4

Offset adjust‐

ment

Command to trim the

lower range value of

the loop current.
Simulate a loop current

of 4.0 mA, measure the

current with an ampere

meter and write the

measured value to this

0 - 25

Write on‐

9388

Float / 4

Gain adjustment Command to trim the

upper range value of

the loop current.
Simulate a loop current

of 20.0 mA, measure

the current with an am‐

pere meter and write

the measured value to

this register.

0 - 25

Write on‐

Channel 4 frequency output settings

Table 4-44

Channel 4 frequency output settings

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

9404

Unsigned / 2

Process value

Select process value

for the current output.

● 0: Mass flow
● 1: Volume flow
● 2: Density
● 3: Medium

temperature

Read /

write

9410

Unsigned / 2

Flow direction

Flow direction filter ap‐

plicable for Process val‐

ues (9404) set to 0, 1,

19, or 27.

● 0: Positive direction
● 1: Negative direction
● 2: Positive and

negative directions

● 3: Positive and

negative directions
(symmetric mode)

Read /

write

9435

Float / 4

Frequency val‐

ue high

Upper frequency value.

Upper nominal output

range boundary.

10000.0

[Hz]

0.0 - 12500.0

Read /

write

9437

Float / 4

Frequency val‐

ue low

Lower frequency value.

Lower nominal output

range boundary.

0.0 Hz

0.0 - 12500.0

Read /

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

112

Function Manual, 06/2018, A5E39931813-AB

Содержание SITRANS F Coriolis FCT030







































































































































































































Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы:

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 112 / 198

Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы: