Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 198

Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 64

Manual zero point adjustment

In case an automatic zero point adjustment cannot be performed, it is possible to do a manual

zero point adjustment by entering the zero point offset value.
1. Select Modbus address 2132 Zero Point Adjustment and set the value to 1 = Manual Zero

Point Adjustment.

2. Select Modbus address 2133 Manual Zero Point Offset and enter the desired offset value.

4.10.5.5

Quality codes for process values

Table 4-15

Quality codes for process value

Modbus

register

Data type /

Size in bytes

Parameter

Description Default value

[units]

(units register)

Value range /

Setting options

Access

level

7409

Unsigned / 2

Mass flow sta‐

tus

Quality sta‐

tus code of

the process

value Mass

flow

● Limit status bit 4 & 5:
● 11: Constant
● 01: Low limited
● 10: High limited
● 00: Not limited
● Process data status bit 6 & 7:
● 11: Good
● 01: Poor Accuracy
● 10: Manual / Fixed
● 00: Bad

Read

only

7509

Unsigned / 2

Volume flow

status

Quality sta‐

tus code of

the process

value Vol‐

ume flow

● Limit status bit 4 & 5:
● 11: Constant
● 01: Low limited
● 10: High limited
● 00: Not limited
● Process data status bit 6 & 7:
● 11: Good
● 01: Poor Accuracy
● 10: Manual / Fixed
● 00: Bad

Read

only

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

64

Function Manual, 06/2018, A5E39931813-AB

«
...
62
63
64
65
66
...
»

Содержание SITRANS F Coriolis FCT030







































































































































































































Отзывы:

Нет отзывов