manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 61 / 198

Поделиться
Скачать
Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 61

4.10.5.3

Aerated flow

Table 4-14

Aerated Flow     

HMI menu ID Parameter

Description

Default value 

[unit]

Value range

Access level

3.9.1

Aerated Flow Filter

Set the process value filter for 

aerated flow. Auto means that 

filtering starts automatically 

when measuring aerated flow.

Auto

(non-SIL var‐

iants)

Off

(SIL variants)

● Off
● On
● Auto

User

3.9.2

Filter Time Constant

"Select process value filter level.

* 0.5: Low … 30: High"

10 seconds

● 10 

seconds

● 20 second
● 30 

seconds

● User 

defined 
value

User

3.9.3

Alarm Limit

Set alarm limit in percent of ac‐

cepted bad measurements.

80

[%]

 0 to 99

Expert

3.9.4

Warning Limit

Set warning limit in percent of 

accepted bad measurements.

0

[%]

0 to 99

Expert

3.9.5

Measurement Sample 

Time

Set the time period over which 

the actual percentage of unsta‐

ble measurements is calculated

5

[s]

1 to 10

Expert

3.9.6

Filter Start Hysteresis

Set the hysteresis value. The fil‐

ter is active when the hysteresis 

value is exceeded.

0.02

[mV]

0 to 0.124

Expert

3.9.7

Minimum Filtering Time Set the filtering time. The filter‐

ing time is reset each time hys‐

teresis band is exceeded.

100

[cycles]

0 to 65535

Expert

3.9.8   

Filter Iteration

Set the number of times to re‐

peat the same filter. Increasing 

the number will increase the 

damping.

3

1 to 5

Expert

3.9.9   

Bandwidth Factor

Increase the Bandwidth Factor 

to reduce the LP (low pass) 

bandwidth filtering.

2

0 to 4

Expert

3.9.10

Filter Pole Shift

Configure the bandwidth and 

damping in the stop band. A high 

number will give a small band‐

width and an increased damping 

in the stop band.

2

1 to 5

Expert

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

61

Содержание SITRANS F Coriolis FCT030







































































































































































































Отзывы:

Нет отзывов