manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 135 / 198

Поделиться
Скачать
Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 135

4.10.5.12

Process value filter masks

Process value filter masks

Table 4-58

Process value filter masks   

Selected view type

Setting options

Process value filter mask 1

Bit coded mask to specify the process values that are filtered. Bit set 

means filtered:
● 0: Mass flow
● 1: Volume flow
● 2: Density
● 3: Medium temperature
● 4: Standard Volume Flow
● 5: Fraction Flow Media A 
● 6: Fraction Flow Media B
● 7: Fraction Flow Media A in Percent 
● 8: Fraction Flow Media B in Percent 
● 9: Reference density
● 10: Transmitter internal temperature
● 11: Totalizer 1
● 12: Totalizer 2
● 13: Totalizer 3
● 17: Sensor frame temperature

4.10.6

Maintenance and diagnostics

Table 4-59

Maintenance & diagnostics   

Modbus 

register

Data type / 

Size in 

bytes

Parameter

Description

Default value 

[unit]

(unit register)

Value range / 

Setting op‐

tions

Access 

level

6004

Unsigned / 

4

Configuration 

counter

Configuration counter.

Counts number of parame‐

ter content modified.

-

-

Read only

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

135

Содержание SITRANS F Coriolis FCT030







































































































































































































Отзывы:

Нет отзывов