Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 86

Страница: 86 / 198

Channel 2 frequency output settings

Table 4-32

Channel 2 frequency output settings

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

8904

Unsigned / 2

Process value

Select process value

for the current output.

● 0: Mass flow
● 1: Volume flow
● 2: Density
● 3: Medium

temperature

Read /

write

8910

Unsigned / 2

Flow direction

Flow direction filter ap‐

plicable for Process val‐

ues (8904) set to 0, 1,

19, or 27.

● 0: Positive direction
● 1: Negative direction
● 2: Positive and

negative directions

● 3: Positive and

negative directions
(symmetric mode)

Read /

write

8935

Float / 4

Frequency val‐

ue high

Upper frequency value.

Upper nominal output

range boundary.

10000.0

[Hz]

0.0 - 12500.0

Read /

write

8937

Float / 4

Frequency val‐

ue low

Lower frequency value.

Lower nominal output

range boundary.

0.0

[Hz]

0.0 - 12500.0

Read /

write

8915

Float / 4

Upper range

value volume

flow

Upper volume flow val‐

ue that is mapped to

the upper nominal

range boundary selec‐

ted by Frequency value

high (8935). Applicable

if Process value (8904)

= 1.

0.4 % • max.

volume flow

/s]

(7500)

Read /

write

8917

Float / 4

Lower range

value volume

flow

Lower volume flow val‐

ue that is mapped to

the lower nominal

range boundary selec‐

ted by Frequency value

low (8937). Applicable

if Process value (8904)

= 1.

0.0

/s]

(7500)

Read /

write

8911

Float / 4

Upper range

value mass flow

Upper mass flow value

that is mapped to the

upper nominal range

boundary selected by

Frequency value high

(8935). Applicable if

Process value (8904) =

0.2 • max.

mass flow-

[kg/s]

(7400)

Read /

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

Содержание SITRANS F Coriolis FCT030







































































































































































































Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы:

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 86 / 198

Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы: