Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 23

Страница: 23 / 188

Description

Applications

This electrical machine has been designed for a wide range of drive and energy conversion

applications. The machines are characterized by extreme ruggedness, long service life, and

overall reliability. They are also highly versatile, allowing them to be tailored to specific

functions.
Details of the supplied machine and permissible operating conditions can be found in this

documentation.
The machine was designed in accordance with the ordering party's specification and may only

be used for the contractually agreed purpose. The permissible operating conditions are

specified on the rating plate. The technical data are described in the catalog.

Ex nA or Ex ec type of protection

This machine has Ex nA or Ex ec type of protection according to IEC / EN 60079-15 or -7. It

can therefore be operated in hazardous areas of Zone 2 according to IEC / EN 60079‑10-1.

WARNING

Explosion hazard
This machine is not designed for use in areas at risk of dust explosion or in areas where an

explosion hazard exists due to hybrid mixtures. An explosion can occur if the machine is

operated in these areas. This can result in death, serious injury or material damage.
● Never operate this machine in the presence of explosive dust or in areas where an

explosion hazard exists due to hybrid mixtures.

Machine design

The regulations and standards used as the basis to design and test this machine are stamped

on the rating plate.
The machine design basically complies with the subsequent standards. Please refer to the EU

Declaration of Conformity for the versions of the harmonized standards referenced.

Table 3-1

Machine design

Feature

Standard

Rating and performance

IEC/EN 60034‑1

Degree of protection

IEC/EN 60034‑5

Cooling

IEC/EN 60034‑6

Type of construction

IEC/EN 60034‑7

SIMOTICS FD 1MH1

Operating Instructions 08/2017

Содержание SIMOTICS FD 1LL1





























































































































































































Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды

Siemens SIMOTICS FD 1LL1, Инструкция по эксплуатации и установке

Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды