Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 66

Страница: 66 / 188

Note
Store the rotor locking device
Be sure to store the rotor locking device. It must be remounted for possible disassembly and

transport.

5.2.5

Removing anti-corrosion protection

Machined, bare metallic surfaces of the motor, such as the shaft end, fitted key, foot and flange

surfaces, are treated with an anti-corrosion agent.
1. Remove this layer of anti-corrosion agent from the mounting surfaces of the motor by wiping

it away with an absorbent cloth or paper sheet.

NOTICE
Damage to the machine surface
Using metal objects such as scrapers, spatulas, or plates to remove the anti-corrosion

protection could result in damage to the surfaces of the machine parts.

2. Then lightly oil the bare surfaces again.

5.2.6

Mounting the output elements

Balance quality

The rotor is dynamically balanced. For shaft extensions with featherkeys, the balancing type

is specified using the following coding on the face of the drive end of the shaft:
● "H" means balancing with a half feather key
● "F" means balancing with a whole feather key

Figure 5-1

Balancing type on the drive-end side

Assembly
5.2 Lift the machine to where it will be installed, and position it

SIMOTICS FD 1MH1

Operating Instructions 08/2017

Содержание SIMOTICS FD 1LL1





























































































































































































Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды

Siemens SIMOTICS FD 1LL1, Инструкция по эксплуатации и установке

Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды