Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 143

Страница: 143 / 188

9.1.11

Cleaning the cooling water ducts

To ensure proper functioning of the machine cooling system, the cooling water ducts must be

free of dirt deposits.
● Have the cooling water ducts cleaned by a specialist company. Cleaning devices are

connected to the coolant connections. Dirt is dissolved and rinsed out through the circulation

of suitable solutions in the cooling water ducts.

● You can also remove limescale deposits with a commercially available scale solvent.

9.1.12

Touch up any damaged paintwork

If the paint is damaged, it must be repaired in order to protect the unit against corrosion.

Note
Paint system
Contact the Service Center (Page 177) before you repair any paint damage. They will provide

you with more information about the correct paint system and methods of repairing paint

damage.

9.1.13

Repainting

WARNING

Explosion hazard caused by incorrect painting
The paint coat can become electrostatically charged where there is a thick coat. Electrostatic

discharges can occur. There is a risk of explosion if potentially explosive mixtures are also

present at this moment. This can result in death, serious injury or material damage.

You must comply with one of the following requirements when you repaint painted surfaces:
● Limit the total paint film thickness according to the explosion protection group:

– IIA, IIB: Total paint coating thickness ≤ 2 mm
– IIC: Overall coating thickness ≤ 0.2 mm for motors of group II (gas)

● Limit the surface resistance of the paint used:

– Surface resistance ≤ 1 GΩ for motors of groups II and III (gas and dust)

Maintenance

9.1 Inspection and maintenance

SIMOTICS FD 1MH1

Operating Instructions 08/2017

143

Содержание SIMOTICS FD 1LL1





























































































































































































Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды

Siemens SIMOTICS FD 1LL1, Инструкция по эксплуатации и установке

Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды