Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 188

background image

Safety information

2

2.1

Information for the nominated person in control of the electrical

installation

This electric machine has been designed and built in accordance with the specifications

contained in Directive 2014/35/EU ("Low-Voltage Directive") and is intended for use in

industrial plants. Please observe the country-specific regulations when using the electric

machine outside the European Community. Follow the local and industry-specific safety and

setup regulations.
The persons responsible for the plant must ensure the following:
● Planning and configuration work and all work carried out on and with the machine is only

to be done by qualified personnel.

● The operating instructions must always be available for all work.
● The technical data as well as the specifications relating to the permissible installation,

connection, ambient and operating conditions are taken into account at all times.

● The specific setup and safety regulations as well as regulations on the use of personal

protective equipment are observed.

Note
Use the services and support provided by the appropriate Service Center (Page 177) for

planning, installation, commissioning, and servicing work.

You will find safety instructions in the individual sections of this document. Follow the safety

instructions for your own safety, to protect other people and to avoid damage to property.
Observe the following safety instructions for all activities on and with the machine.
This machine has been designed and built in accordance with Directive 2014/34/EU

("Explosion Protection Directive") and is intended for use in industrial plants with potentially

explosive atmosphere.
Commissioning in the European Community in accordance with Directive 2006/42/EU

(“Machinery Directive”) is forbidden until the plant into which the machine will be installed has

been shown to conform with this directive. Please observe the country-specific regulations

when using the machine outside the European Community.

WARNING

Risk of explosion with commissioning prior to determining the conformity
If the machine is commissioned prior to determining the plant conformance, the explosion

protection of the plant is not ensured. An explosion can occur. This can result in death, serious

injury or material damage.
Do not commission the machine until it has been confirmed that the plant conforms with the

explosion protection directive.

SIMOTICS FD 1MH1

Operating Instructions 08/2017

15

«
...
13
14
15
16
17
...
»

Содержание SIMOTICS FD 1LL1





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMOTICS FD 1LL1

Бренд: AL-KO Страницы: 182

Бренд: YOODA Страницы: 6

Бренд: Flux Страницы: 28

Бренд: CG Страницы: 45

Бренд: Briggs & Stratton Страницы: 6

Бренд: Power Fist Страницы: 40

Бренд: REXROTH Страницы: 86

Бренд: Plettenberg Страницы: 26

Бренд: Danfoss Страницы: 77

Бренд: DIMOEL Страницы: 8

Бренд: DLE Страницы: 4

Бренд: Komatsu Utility Страницы: 32

Бренд: Toyama Страницы: 48

Бренд: Volvo Penta Страницы: 96

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 38

Бренд: Detroit Diesel Страницы: 174

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды