Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 188

background image

3. If it runs perfectly, connect a load.

NOTICE
Thermal overload of motors connected directly to the line supply
In addition to the load torque, the ramp-up (accelerating) time is essentially influenced by

the moment of inertia to be accelerated. While ramping up when connected to the line

supply, the inrush (starting) current is a multiple of the rated current. This can result in

thermal overload. This can damage the motor.
As a consequence, when ramping up, observe the following:
● Monitor the ramp-up time and number of consecutive starts.
● Comply with the limit values and/or ramp-up conditions specified in the catalog or the

order documentation.

4. During the test run, check and document the following:

– Check whether it is running smoothly.
– Document the voltage, current and power values. As far as possible, document the

corresponding values of the driven machine.

– If this is possible using the available measuring equipment, check the bearing and stator

winding temperatures until they have reached steady-state values.

– Check the machine for noise or vibrations on the bearings or bearing shields as it runs.

5. In case of uneven running or abnormal noise, switch off the machine. As the machine runs

down, identify the cause.
– If the mechanical operation improves immediately after the machine is switched off, then

the cause is magnetic or electrical.

– If the mechanical running does not improve immediately after switching the machine off,

then the cause is mechanical.

- Imbalance of the electrical machine or the driven machine

- The machine set has not been adequately aligned

- The machine is being operated at the system resonance point. System = motor, base

frame, foundation, ...

NOTICE
Serious damage to the machine
If the vibration values in operation are not maintained in accordance with DIN ISO 10816-3,

then the machine can be mechanically destroyed.
● During operation, observe the vibration values in accordance with DIN ISO 10816‑3.

Note
You can find more information in Chapter 2 of catalog D81.8.

Start-up

7.8 Test run

SIMOTICS FD 1MH1

Operating Instructions 08/2017

111

«
...
109
110
111
112
113
...
»

Содержание SIMOTICS FD 1LL1





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMOTICS FD 1LL1

Бренд: W&H Страницы: 42

Бренд: Scania Страницы: 83

MaxxForce DT 10

Бренд: Navistar Страницы: 109

Бренд: Lenze Страницы: 36

Бренд: KYMCO Страницы: 244

Бренд: Siemens Страницы: 50

Worm Gearbox S 5 BA 2012

Бренд: Siemens Страницы: 54

SINAMICS S120 1PM4

Бренд: Siemens Страницы: 100

SIMOTICS-T 1FW6 Series

Бренд: Siemens Страницы: 106

SIMOTICS XP 1MD4

Бренд: Siemens Страницы: 128

SIMOTICS TN 1LL8

Бренд: Siemens Страницы: 148

SIMOTICS XP 1MB155

Бренд: Siemens Страницы: 152

SIMOTICS XP 1MB5 SH400

Бренд: Siemens Страницы: 166

Бренд: Siemens Страницы: 170

SIMOTICS XP 1LA5

Бренд: Siemens Страницы: 174

SIMOTICS-T 1FW68

Бренд: Siemens Страницы: 180

SINAMICS S 1PH7

Бренд: Siemens Страницы: 244

Бренд: Siemens Страницы: 512

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды