Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 160

Страница: 160 / 188

10.7

Roller bearing cartridge at the drive and non-drive end

The following description applies to the standard version for IM B3. The bearing type used is

stamped on the lubricant plate. Different bearings can be used for different types of

construction.
As of shaft height 400, fast running motors have bearing cartridges with a reduced diameter

in the bearing housing design.

Figure 10-3 Bearing cartridge at the drive end and non-drive end

Table 10-3

Spare parts for the bearing cartridge at the drive end and non-drive end

Part

Description

Part

Description

3.20

Outer bearing cover

4.20

Outer bearing cover

3.35

Grease slinger

4.35

Grease slinger

3.60

Inner bearing cover

4.60

Inner bearing cover

5.00

End shield

6.00

End shield

Bearing kit at the drive end and non-drive end consists of the following components
Deep-groove ball bearing (locating bearing)

Deep-groove ball bearings

Shaft sealing ring, labyrinth ring (optional)

Shaft sealing ring

Locking ring, guard ring

Locking ring

Spare parts
10.7 Roller bearing cartridge at the drive and non-drive end

SIMOTICS FD 1MH1

160

Operating Instructions 08/2017

Содержание SIMOTICS FD 1LL1





























































































































































































Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды

Siemens SIMOTICS FD 1LL1, Инструкция по эксплуатации и установке

Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды