Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 188

background image

WARNING

Center of gravity not centered
If the center of gravity of a load is not located centrally between the attachment points, the

machine can tip over or slip out of the lifting equipment and fall when it is being transported

or lifted. This can result in death, serious injury or material damage.
● Comply with the handling instructions on the machine when transporting it.
● Be aware of the possibility of different loads on the sling ropes or lifting straps and the

carrying capacity of the lifting equipment.

● Always take account of the center of gravity when transporting or lifting the machine. If

the center of gravity is not located centrally between the attachment points, then position

the hoisting hook above the center of gravity.

4.18.3

Securing the rotor

Depending on the version, the machine is fitted with a rotor shipping brace. This protects the

bearings against damage due to shock and vibration during transport or storage.

NOTICE
Vibration and shock during transport
Not using the rotor shipping brace can cause damage to the machine if it is jolted during

transport. Material damage can result.
● If the machine is fitted with a rotor shipping brace, this should always be used when

transporting the machine. The rotor shipping brace must be attached during the transport.

● Only remove it before pulling on the output element.
● For machines with a vertical type of construction:

– Do not remove the rotor shipping brace until the machine is in a vertical position.
– If a machine has to be transported in a horizontal position, the rotor must be fixed in

position before the machine is turned onto its side. Vertical machines can be supplied

in the horizontal position from the manufacturing plant.

Preparations for use
4.18 Transport and storage

SIMOTICS FD 1MH1

46

Operating Instructions 08/2017

«
...
44
45
46
47
48
...
»

Содержание SIMOTICS FD 1LL1





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMOTICS FD 1LL1

Vanguard 290000

Бренд: Briggs & Stratton Страницы: 68

Бренд: KCFA Страницы: 2

Бренд: Nanni Страницы: 24

Бренд: Nord Drivesystems Страницы: 112

24 v High Performance Synchronous Motor

Бренд: Rega Страницы: 1

Бренд: Crestron Страницы: 2

Бренд: Yanmar Страницы: 248

Бренд: Sanyo Denki Страницы: 20

Бренд: Honda Страницы: 15

Бренд: Honda Страницы: 60

Бренд: LONCIN Страницы: 23

Бренд: STEYR Страницы: 118

KODIAK MARINE LT4 SUPERCHARGED

Бренд: KEM Страницы: 66

Бренд: Yanmar Страницы: 20

Бренд: Yanmar Страницы: 50

Бренд: Yanmar Страницы: 50

Бренд: Yanmar Страницы: 65

Бренд: Yanmar Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды