Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 148

Страница: 148 / 188

9.2.3.2

Remove V ring

Depending on the particular version, there is a V ring. The V ring must be replaced if unusual

amounts of grease escape the roller bearing or the V ring is visibly damaged.

Figure 9-1

Remove the V ring

1. Mark the components so that they can be correctly assembled.
2. Remove the V ring

①

with the bearing cap – or by using a suitable tool from the shaft.

Removing the protective ring for IP56 degree of protection

The V ring for the outer bearing seal is fitted with a protective ring

②

for degree of protection

IP56. The protective ring does not have to be removed for disassembling the bearing bush.
● Remove the protective ring together with the V ring and the outer bearing cover or end

shield from the shaft.

Содержание SIMOTICS FD 1LL1





























































































































































































Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды

Siemens SIMOTICS FD 1LL1, Инструкция по эксплуатации и установке

Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды