Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 188

background image

2.8

Interference immunity

By selecting suitable signal cables and evaluation units, companies operating complete plants

and systems must ensure that the interference immunity of the machine is not diminished.

2.9

Influence on the line power supply through a strongly irregular torque

A strongly irregular torque, for example with the drive of a reciprocating motor, forces a non-

sinusoidal motor current. The emerging harmonics can have an impermissible influence on

the line power supply via the connection lines.

2.10

Interference voltages when operating the converter

WARNING

Interference voltages when operating the converter
When a converter is in operation, the emitted interference varies in strength depending on

the converter (manufacturer, type, interference suppression measures undertaken). On

machines with integrated sensors (e.g. PTC thermistors), interference voltages caused by

the converter may occur on the sensor lead. This can cause faults which can result in eventual

or immediate death, serious injury or material damage.
● Comply with the EMC information provided by the manufacturer of the converter. This is

how you prevent the limit values stipulated by IEC/EN 61000-6-3 for the drive system

(consisting of the machine and converter) from being exceeded.

● You must put appropriate EMC measures in place.

2.11

Electromagnetic fields when operating electrical power engineering

installations

WARNING

Interference to electronic devices caused by electrical power equipment
Electrical power equipment generate electric fields during operation. Potentially lethal

malfunctions can occur in medical implants, e.g. pacemakers, in the vicinity of electrical power

equipment. Data may be lost on magnetic or electronic data carriers.
● It is forbidden for people with pacemakers to enter the vicinity of the machine.
● Protect the personnel working in the plant by taking appropriate measures, such as

erecting identifying markings, safety barriers and warning signs and giving safety talks.

● Observe the nationally applicable health and safety regulations.
● Do not carry any magnetic or electronic data media.

Safety information

2.8 Interference immunity

SIMOTICS FD 1MH1

Operating Instructions 08/2017

21

«
...
19
20
21
22
23
...
»

Содержание SIMOTICS FD 1LL1





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMOTICS FD 1LL1

Бренд: VEM Страницы: 16

Бренд: GAPOSA Страницы: 20

Бренд: Habasit Страницы: 54

Бренд: Exalto Страницы: 28

Бренд: Mitsubishi Electric Страницы: 102

Бренд: Wilesco Страницы: 2

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 4

SOLIDline-MOR GU4510

Бренд: GEIGER Страницы: 8

Бренд: Yanmar Страницы: 213

Бренд: Germany Motions Страницы: 12

Бренд: RIEJU Страницы: 63

Бренд: Just Motion Control Страницы: 21

Бренд: Yanmar Страницы: 2

Бренд: Yanmar Страницы: 266

Бренд: O.S. Speed Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды