Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 91

Страница: 91 / 188

6.4.5

Connection without terminal box

If the machine was ordered without terminal box (where the cables are simply brought out of

the motor), then the proper connection must be made in an external terminal box.

WARNING

Incorrect dimensioning
Faults can occur if the appropriate technical data is not complied with when connecting up.

For instance, degree of protection, minimum air and creepage distances. These faults can

result in eventual or immediate death, serious injury or material damage.
● Ensure that the external terminal box is dimensioned according to the data on the rating

plate and is suitable for the respective use.

If the motor has been ordered with brought-out leads, in this case you must comply with the

relevant conditions for Zone 2. It is assumed that the buyer, the installer and users of the

installation are familiar with these conditions and will carefully observe them.

6.4.6

Connecting the machine for a specific direction of rotation

If the machine has one shaft extension or two shaft extensions with different diameters, the

direction of rotation when looking at the front of the single or the thicker shaft extension is

defined as follows:
● If you connect the power cables in the phase sequence L1, L2, L3 to U, V, W, the resulting

rotation will be clockwise.

● If you interchange two connections, e.g. L1, L2, L3 to W, V, U, the resulting rotation will be

counter-clockwise.

● On machines which are only allowed to run in one direction, the rating plate shows an arrow

which indicates the permitted direction of rotation, and it also specifies the terminal

connections in the required phase sequence.

NOTICE
Incorrect direction of rotation
The machine will not be adequately cooled if it is operated other than how it was originally

ordered or with the incorrect direction of rotation. This can result in machine damage.
Observe the direction of rotation data on the nameplate.

Electrical connection

6.4 Preparation

SIMOTICS FD 1MH1

Operating Instructions 08/2017

Содержание SIMOTICS FD 1LL1





























































































































































































Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды

Siemens SIMOTICS FD 1LL1, Инструкция по эксплуатации и установке

Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды