Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 42

Страница: 42 / 188

4.10

Support base for IM B5 construction type

● For machines, type of construction IM B5, provide an additional support foot at the NDE.

The support foot is not included in the scope of supply.

● Use an appropriately sized support foot with the appropriate rigidity. The support foot must

be able to support the total weight of the machine.

The weight of the machine is stated on the rating plate, data on geometry is shown in the

dimension drawing.

● There is a threaded hole M36 at the bottom of the machine where you can attach the support

foot.

WARNING

Missing support at the NDE
If the machine has no support at the NDE, the flange cannot hold the weight of the machine.

The machine or machine parts may loosen.
This can result in death, serious injury or material damage.
● Use an appropriately sized support base.

4.11

Noise emissions

WARNING

Noise emissions
During operation, the machine's noise emission levels can exceed those permitted at the

workplace, which can cause hearing damage.
Take steps to reduce noise, such as introducing covers and protective insulation or adopting

hearing protection measures, so that the machine can be operated safely within your system.

4.12

Rotational speed limit values

WARNING

Excessively high speeds
Excessive rotational speed can lead to serious damage to the machine. This can result in

death, serious injury, or material damage.
● Avoid operation above the permissible speed by using the appropriate control function.
● Observe the speeds stamped on the rating plate.

Preparations for use
4.10 Support base for IM B5 construction type

SIMOTICS FD 1MH1

Operating Instructions 08/2017

Содержание SIMOTICS FD 1LL1





























































































































































































Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды

Siemens SIMOTICS FD 1LL1, Инструкция по эксплуатации и установке

Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды