Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 188

background image

8.6.1

Avoidance of frost and corrosion damage in the cooling system

● For avoidance of frost and corrosion damage, completely drain the water from the cooling

system. Then blow air through the cooling system to dry it.

If the cooling system cannot be drained because standby capability is required at short

notice, protect the cooling circuit against frost and corrosion damage. To do this, add

suitable additives to the cooling water.

NOTICE
Impairment of the heat transport
Additives such as anti-freeze and corrosive inhibitor can impair the heat transport.
Operate the motor only with the contractually agreed water quality.

For avoidance of deposits, the cooling water circuit must then be kept running. So as to be

certain of excluding the possibility of formation of condensation within the machine, the anti-

condensation heating should also remain switched on (if fitted).

8.6.2

Avoidance of condensation or formation of condensation within the machine

● If the controller does not do this automatically, switch on any anti-condensation heating

during stoppages. This will avoid the formation of condensation.

● Do not switch on the anti-condensation heating for at least two hours after the motor has

been switched off. This prevents damage to the winding insulation.

WARNING

Explosion hazard
If the anti-condensation heating is switched on directly after the machine is switched off, the

temperature class or the maximum surface temperature of the machine can be exceeded.
In an explosive atmosphere, there is a risk of an explosion. This can result in death, serious

injury or material damage.
● Only switch on the anti-condensation heating after the motor has been switched off.

Carefully comply with the data on the anti-condensation heating plate.

Operation

8.6 Stoppages

SIMOTICS FD 1MH1

Operating Instructions 08/2017

125

«
...
123
124
125
126
127
...
»

Содержание SIMOTICS FD 1LL1





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMOTICS FD 1LL1

Бренд: Fagor Страницы: 174

Бренд: Isuzu Страницы: 174

Бренд: Lenze Страницы: 64

Бренд: Stuart Turner Страницы: 20

Бренд: Farymann Diesel Страницы: 76

Бренд: RHINO Страницы: 20

COMBIFLUX FP 314 PVDF

Бренд: Flux Страницы: 28

NIIGATA MG(L)26HLX

Бренд: IHI Страницы: 204

Бренд: Cobra Страницы: 15

Бренд: MTD Страницы: 44

Бренд: Bison Страницы: 19

4.2-litre V8 FSI

Бренд: Audi Страницы: 48

Бренд: Black Bruin Страницы: 4

Бренд: Asmo Marine Страницы: 8

Parilla Norswift 60cc

Бренд: IAME Страницы: 25

POWER STROKE 2013

Бренд: Ford Страницы: 95

Бренд: Seidel Страницы: 12

Бренд: Nakanishi Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды