Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 173

Страница: 173 / 188

Disposal

Protecting the environment and preserving its resources are corporate goals of the highest

priority for us. Our worldwide environmental management system to ISO 14001 ensures

compliance with legislation and sets high standards in this regard. Environmentally friendly

design, technical safety and health protection are always firm goals even at the product

development stage.
Recommendations for the environmentally friendly disposal of the machine and its components

are given in the following section. Be sure to comply with local disposal regulations.

11.1

RoHS - restricting the use of certain hazardous substances

In compliance with RoHS ("Restriction of certain Hazardous Substances" ) we replace

substances that are damaging to the environment by those that are not based on state-of-the-

art technology. In doing so, safety in operation and handling will take priority at all times.

Note
Country-specific legislation
When disposing of the machine or of waste that is created during the individual phases of its

life cycle, please observe the statutory requirements applicable in the country of use.

11.2

Preparing for disassembly

Disassembly of the machine must be carried out and/or supervised by qualified personnel with

appropriate expert knowledge.
1. Contact a certified waste disposal organization in your vicinity. Clarify what is expected in

terms of the quality of dismantling the machine and provision of the components.

2. Follow the five safety rules (Page 16).
3. Disconnect all electrical connections and remove all cables.
4. Remove all liquids such as oil and cooling liquids. Collect the liquids separately and dispose

of them in a professional manner.

5. Detach the machine fixings.
6. Transport the machine to a suitable location for disassembly.

SIMOTICS FD 1MH1

Operating Instructions 08/2017

173

Содержание SIMOTICS FD 1LL1





























































































































































































Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды

Siemens SIMOTICS FD 1LL1, Инструкция по эксплуатации и установке

Результаты поиска

Содержание SIMOTICS FD 1LL1

Отзывы:

Похожие инструкции для SIMOTICS FD 1LL1

Бренды по названию

Популярные бренды