Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 188

background image

● 1XB7740

– For 12 or fewer cables and lower cross-sections, you can rotate the terminal box with

installed stator cables through ±90°.

– For more than 12 cables - or for cables with a cross-section greater than 50 mm² - you

must remove the internal stator cables before rotating the terminal box.

● 1XB7750

– Remove the internal stator cables before rotating the terminal box.

Rotating a terminal box with mounted stator cables

1. Ensure that the motor is disconnected from the power supply.
2. Release two diagonally opposed screws for the cover, and secure the cover using two M10

threaded bars screwed in diagonally opposing one another. Release the two other screws

and lift the cover off the terminal box. The terminal box cover is very heavy. Especially when

in a lateral position, ensure that the terminal box does not fall down.

3. If the motor is already connected:

– Remove the cables of the power supply.
– Release the screw connection of the cable entry. Remove the cables through the

opening.

4. Remove the grounding straps on two sides of the terminal box lower section.
5. Remove the screwed joints of the lower section with the console or optionally the cable

duct.

6. Screw in two eye-bolts diagonally in the M10 thread at the corners. Slightly raise the terminal

box housing using a crane.

7. Rotate the terminal box through ±90° in the desired direction. Carefully place the terminal

box down. Take care not to damage the seal.

8. Screw the terminal box with the console / cable duct (4 x M16, tightening torque 170 Nm).
9. Fasten the grounding straps to the terminal box lower section and the console or cable duct:

– After rotation, remove the plugs of the two nearest M8 threads on the console or cable

duct.

– Grind the surface at the drilled holes so that the grounding straps have metallic contact.
– Then fasten the two straps to the terminal box lower section and the console or cable

duct (4x M8, tightening torque 11 Nm).

– Protect the bare areas at the contact with corrosion protection.

10.Reconnect the power supply cables. More information:

– Connecting the grounding conductor (Page 89)
– Introducing and routing the cables ...
– Connecting cables ...

11.Screw in the two diagonally arranged threaded bars and slide the cover onto these bars.

Take care not to damage the seal.

Electrical connection
6.3 Terminal box

SIMOTICS FD 1MH1

86

Operating Instructions 08/2017

«
...
84
85
86
87
88
...
»

Содержание SIMOTICS FD 1LL1





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMOTICS FD 1LL1

Бренд: Yamaha Страницы: 7

Бренд: Globe Страницы: 11

Бренд: Northern Lights Страницы: 36

Бренд: Northern Lights Страницы: 45

Бренд: Northern Lights Страницы: 56

Бренд: Volvo Penta Страницы: 53

Бренд: Volvo Penta Страницы: 76

Бренд: Baumr-AG Страницы: 25

Бренд: Volvo Страницы: 8

Бренд: Yanmar Страницы: 142

Бренд: Chicago Pneumatic Страницы: 100

Бренд: DETROIT Страницы: 84

Бренд: DETROIT Страницы: 116

Бренд: Baumuller Страницы: 19

Бренд: Baumuller Страницы: 31

Бренд: Wood-mizer Страницы: 192

Бренд: Mitsubishi Страницы: 219

Бренд: TOSO Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды