Siemens SIMOTICS FD 1LL1 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 188

background image

WARNING

The feather key can fall out
The feather keys are only locked against falling out during shipping. If a machine with two

shaft extensions does not have an output element on one shaft extension, the feather key

can fall out during operation.
Death or serious injury can result.
● Do not operate the machine unless the transmission elements have been pulled on.
● On shaft extensions without output element, make sure that the feather key cannot fall

out and shorten it by approximately half for balance type "H".

5.2.7

Lifting and transportation

To safely lift and transport the machine, the following requirements must be met:
● Personnel operating cranes and fork-lift trucks must be appropriately qualified.
● If the machine is packed, depending on the weight, size and on-site conditions, lift crates

and transport frames using a fork-lift truck or a crane with slings. Use a crane or fork-lift

truck suitable for the load.

● When lifting the machine, use only approved and undamaged sling guides and spreaders

of sufficient rated capacity. Check the lifting equipment prior to its use. The weight of the

machine is shown on the rating plate.

● When lifting the machine, refer to the information on the lifting plate.

– Comply with the specified spreading angles.
– Do not exceed the maximum lifting acceleration and lifting speed specified on the lifting

plate. Lift the machine without jerking it.

Acceleration a ≤ 0.4 g (≈ 4 m/s

2

)

Velocity v ≤ 20 m/min

WARNING

Transport for a different type of construction
If you do not transport or lift the machine in a position appropriate for its construction, the

machine can tip, slip into the lifting equipment or fall down. This can result in death, serious

injury or material damage.
● Use only the load carrying device on the stator frame for lifting.
● Use the load carrying device appropriate for the machine position.
● Only use suitable rope guiding or spreading devices.

Assembly
5.2 Lift the machine to where it will be installed, and position it

SIMOTICS FD 1MH1

68

Operating Instructions 08/2017

«
...
66
67
68
69
70
...
»

Содержание SIMOTICS FD 1LL1





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMOTICS FD 1LL1

Бренд: FAAC Страницы: 28

Бренд: Vanguard Страницы: 120

Бренд: Keyde Страницы: 4

MULTI-VANE 1800 Series

Бренд: Ingersoll-Rand Страницы: 12

Бренд: Stuart Turner Страницы: 20

Бренд: Polini Страницы: 34

Бренд: Daedong Страницы: 66

Бренд: Simple Motors Страницы: 6

Бренд: PIREZ Страницы: 26

Бренд: Pratt & Whitney Canada Страницы: 48

Бренд: O.S. engine Страницы: 22

Бренд: O.S. engine Страницы: 29

Бренд: Amewi Страницы: 20

Бренд: Briggs & Stratton Страницы: 112

Бренд: Continental Refrigerator Страницы: 348

Бренд: Wood-mizer Страницы: 146

Бренд: Toyota Страницы: 138

Бренд: Toyota Страницы: 174

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды