Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 135 / 136

Index

SIMATIC IPC1047
Operating Instructions, 09/2018, A5E45118479-AA

135

Power consumption, 107

Power Good Signal, 111

Power requirements, 110

Power supply, 13, 36

AC power supply, 112

Redundant, 13

Power supply

AC supply voltage, 111

Processor, 13

Removal, 89

Processor type, 90

Protection class, 107

Protective measure

Static electricity, 104

RAID, 117, 118

RAID controller

Making known to the operating system, (See

storage controllers)

RAID system, 44

Checking status, 77

Displaying the defective HDD in the RAID

software, 78

Integrating a new hard disk, 80

Management functions, 42, 45, 77

SAS hardware RAID, 44

RAID1 system, 46

Mounting locations for hard disk drives, 60

Replacing a defective hard disk drive, 61

Rear view, 14, 15

Recovery, 93

Removing

Device fan, 83

Processor, 89

Repairs, 73, 74

Restore, 90

Safety information

Storage, 29

Transportation, 29

Safety instructions

Device and system extensions, 25

General, 19

I/O devices, 26

Mounting, 23

Power supply, 36

Transportation and storage, 22

Safety regulations, 107

SAS, 44

SAS Hardware RAID, 109

SAS Hardware RAID system, 44

Serial number, 27

Slave drive, (Multi-disk system)

Slots, 12

Static electricity

Protective measures, 104

Status displays, 16

Ethernet interface, 17

LED, 18

Power supply, redundant, 18

Status indicators, (Status displays)

Storage, 22

Supply voltage, 36, 107

Switching off the device

Disconnecting from the line voltage, 47

Forced shutdown, (Hardware reset)

Hardware reset, 47

Shutting down the operating system, 46

Switching on the device

Configure automatic startup, 41

System partition, 90

Target system, 90

Telescopic rails, 32

Temperature, 108

Third-party expansion cards, 118

Tools, 74

TPM, 12

Transportation, 22

Troubleshooting, 118

TÜV, 101

UEFI mode

Recovery, 93

Restore, 91

Update,

Updates

Operating system, 92

USB port, 12

User Account Control, 46

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды