Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 96 / 136

Device maintenance and repair

7.6 Installing the software

SIMATIC IPC1047

Operating Instructions, 09/2018, A5E45118479-AA

Refresh

Updating

Load Driver

Integration of controller drivers unknown to the operating system and required for

installation. Please read the information in the section "Information for systems

with RAID or AHCI controller".

Delete

Deleting a partition

Extend

Changing the partition size

Format

Formatting a partition

New

Creating new partitions

Identification for error messages, for example, if the data medium was not

formatted in the required "NTFS" format.

Note
If you want to install the operating system on a data medium connected to a storage

controller unknown to the operating system, you have to integrate the driver of the storage

controller. Integrate this driver before you partition the data medium and before you install

the operating system. For more information on integrating the storage controller, refer to the

section "Information for systems with RAID or AHCI controller".

Make sure that the partition on which you want to install the operating system is large

enough and is set up with a NTFS file system.
The recommended minimum size of this partition varies, depending on the operating

system, how much RAM you have available and how much additional software you want

to use. Information on how the data medium is partitioned in its factory state is available

in the tables below.

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды