Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 94 / 136

Device maintenance and repair

7.6 Installing the software

SIMATIC IPC1047

Operating Instructions, 09/2018, A5E45118479-AA

Procedure

Note
The firmware settings might have to be changed in order for the device to boot from the

provided USB stick.
You can find additional information on this in the description of the firmware/BIOS for the

device.

NOTICE
Risk of data loss
Files, user settings as well as existing authorizations and license keys are lost when the

operating system is installed!

•

Back up your data before installing the operating system.

Insert the provided USB stick into the device.

Reboot the device.

Boot with the provided USB stick in the Boot mode you have set beforehand.

In the Windows Boot Manager, select the "Recovery Microsoft Windows ..." option and

confirm the selection.
The Windows installer starts after a few seconds.

Follow the instructions on the screen.
Note the following information.

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды