Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 80 / 136

Device maintenance and repair

7.3 Manage onboard RAID system

SIMATIC IPC1047

Operating Instructions, 09/2018, A5E45118479-AA

A defective hard disk is still displayed during the rebuilding process. This display disappears

when the rebuilding process is completed.

Procedure - integrating hard disk manually

When the "Automatic rebuild" option is deselected in the "Preferences" menu of the RAID

software (default setting), you must integrate the hard disk manually:
1.

Select "Start" > "Programs" > "Intel Rapid Storage Technology".

Click

"Run Hardware Scan now".

The new hard disk is found and displayed.

Or:
1.

Reboot the device.
The RAID software automatically integrates the hard disk.

Click the "Rebuild to another Disk" link.
The RAID system is synchronized.

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды